Genuine ROTAX Parts

B – Loctite 243
I – Lithium-Base Grease
O – Engine Oil

a – Stator retrofit kits: 912 UL: S/N 3,792.501 up to 3,792.55 Set D P/N 888716, S/N 4,005.300 up to 4,152.111 Set E P/N 888718, S/N 3,792.556 up to 4,005.299, Set C P/N 888714; S/N 4,152.112 up to 4,403.282 Set B P/N 888712; 912 ULS: S/N 4,425.001 up to 4,425.029 Set A P/N 888710; 914 UL: S/N 4,417.503 up to 4,417.783 Set B S/N 888712;
b – With modified trigger, instead of 4° before top dead center --> -3° after top dead center;
c – SI-912-013 / SI-914-016 standardization of the ignition unit;
d – Trigger coil kit with elongated hole for adjustment and 6-pole connector incl. 7 Stk. P/N 827800;
e – 4-pole connector and trigger coils without alignment incl. 7 Stk. P/N 827800. Replaced trigger coil kit P/N 965177;
f – Trigger coils for rev. counter to P/N 965176 and P/N 965179;
g – At all trigger coils with longhole

A – Loctite 221
C – Loctite 648
E – Loctite Anti-Seize
H – Loctite 603
I – Lithium-Base Grease
Q – 732 RTV

AR – As required

a – Replace layshift gear 55 T and pinion shaft 21 T only together;
b – Replace layshift gear 57 T and pinion shaft 19 T only together;
c – Replace layshift gear 59 T and pinion shaft 17 T only together;
d – Replace layshift gear 60 T and pinion shaft 15 T only together;
e – Attention: Left handed thread;
f – Coupling-flange Part No. 958 971 and sealing ring Part No. 950 084 has to be used as a set;
h – Gear set and splitted cone sleeve must be used together;
|| – NOTE: Included starter relay;
See also SI-2ST-007

B – Loctite 243

a – Marked with S/N;
b – Only for TCU P/N 966470;
c – For cylinder 2/4;
d – For cylinder 1/3;
e – Used as water trap;
f – Also included in carburetor for 914 Cyl. 2/4;
g – Drip tray for airbox P/N 867758, 667162 and 667167;
h – For use of airbox P/N 667162. See SI-914-013 current issue;
i – For use of airbox P/N 667167, See SI-914-015 current issue;
j – For use of airbox P/N 867753;
k – New adapter flange use only together with throttle valve position sensor. See SI-25-1997;
l – See Service Instruction SI-914-022 current issue;
m – Optional for fuel pressure gauge connection;
n – Not for TCU P/N 966470

a – Crankcase with screw connection M8x18, b – Marked with groove, c - See Overhaul Manual of the respective engine type, current issue.

A – Loctite 221
D – Loctite 574

a – From engine serial number 4,795.397

A: Loctite 221
L: Molykote PG-54
M: Molykote G-N

AR – As required

d – Starter Rope 3700 mm;
e – Starter Rope 2200 mm;
f – In a roll/sold per meter (39”);
g – Modified rope fixation, knot instead of key clamp (from S/N 5.742.150)

O – Engine Oil

a – See SB-912-040, SB-914-026 current issue;
b – In a roll;
c – With metric connection thread M18x1.5

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
J – Molykote 44 Medium

c – Up to engine S/N 582 UL Mod. 90 4,172.691 (see also SI-08-1994);
d – From engine S/N 582 UL Mod. 90 4,172.692 (see also SI-08-1994)

B – Loctite 243
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
P – Loctite 5910

a – Stainless;
b – Optional for engine suspension frame;
c – The rotary seal was introduced from following S/N. Up to this S/N the rotary seal has to be exchanged together with P/N 850945, 926273, 922224: 912 UL 4,403.283, 912 ULS starting with serial production, 914 UL 4,417.783;
d – For mech. rev counter drive without centering bore for pick up. For engines without mech. rev. counter drive P/N 230880, 945750, 840511 has to be mounted additional; 
e – See SB-914-023 current issue;
f – See Maintenance Manual Heavy of the respective engine type, current issue;
g - Without processing for mech. rev counter drive;
h – Will be delivered in circle shape.

A – Loctite 221
I – Lithium-Base Grease

a – For configuration free-air-cooled;
b – In a roll/Sold per meter (39");
c –  For magneto flywheel new version (with closed cage), Torx screw also valid for old version. At disassembly and reassembly of the screw, the thread has to be cleaned of the remaining coating and secure with Loctite 221. As an alternative a new screw can be used.

a - Air filter incl. hose clamp, b - Double flange, c - Ambient pressure and temperature

A – Loctite 221
B – Loctite 243
C - Loctite 648

a – From engine S/N 582 UL Mod. 90: 4,015.239. and beginning of serial production 582 UL Mod 99;
c – Tighten to leave 1 mm distance between starter cover and electric starter;
d – 582 UL Mod. 90 until engine S/N 4.015.238 (without hydro damper assembly)

A – Loctite 221
I – Lithium-Base Grease

a – For ignition circuit 1;
b – For ignition circuit 2;
c – From engine S/N 4,795.397;
d – Sold by the meter (39");
e – Magneto flywheel new version (with closed cage), torx screw also valid for old version. At disassembly and reassembly of the screw, the thread has to be cleaned of the remaining coating and secured with Loctite 221. As an alternative a new screw can be used.

AR – As required

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
J – Molykote 44 Medium

a – Red 76,00 - 76,01mm, Green 76,01 - 76,02mm;
b – For configuration without 2-piece radiator;
c – For configuration with 2-piece radiator

AR – As required
c – Large. Cooling area 234 cm²/36.27 sq. in., d – Connection metric, e – Connection UNF

B – Loctite 243

a – For cylinder 2 and 1/3;
b – For cylinder 1 and 2/4;
c – Carburetor housing not available as spare part. Use carburetor assembly,
d – Refer to service instruction SI-03-1998 current issue,
e – With clearance for O-ring (use only together with O-ring pos. 18 (P/N 950430);
f – For airbox P/N 867758, P/N 867756; See SB-912-044;
g – See SI-912-012, SI-914-014;
h – Package including two floats;
i – Special jetting according to instructions of the manufacturer;
j – Contain parts requirement for 2 carburetors;
k – Overhaul kit for 1 carburetor