Genuine ROTAX Parts

B – Loctite 243

a – For cylinder 1/3;
b – For cylinder 2/4;
c – Carburetor housing not available as spare part. Use carburetor assembly; 
d – Refer to service instruction SI-03-1998 current issue;
e – With clearance for O-ring (use only together with O-ring pos. 16 P/N 950430);
f – See SI-912-012, SI-914-014 current issue;
g – For airbox P/N 667167, See SI-914-015 current issue, For engine S/N 914 UL 4,418.634;
h – For airbox P/N 867753 or 667162, See SI-914-013 and SI-914-002 current issue;
i – Package including two floats;
j – At carburetor 1/3 only 1 piece;
k – Contain parts requirement for 2 carburetors

B – Loctite 243
I - Lithium-Base Grease
AG – Silicon Heat Compound

a – Sold by the meter (39");
e – Not necessary at intake manifold P/N 867688;
f – Introduced as S/N 04.0388 with altered insulation only for spare parts;
g – Not suitable for crankcase P/N 886354, P/N 886358 and older;
h – At crankcase P/N 888364 or newer crankcase;
i – Not suitable for intake manifold P/N 867688;
j – Necessary at version with ring mount;
k – Sold by the meter (39");
l – Use P/N 842742 and 953390 only together;
m – SI-912-013 / SI-914-016 current issue. See Maintenance Manual Heavy of the respective engine type, current issue. From engine 912 UL S/N 4,406.291, 912 ULS S/N 5,643.680, 914 UL 4,418.712;
n - In a roll, silicone hose 120 mm;
o – SI-912-020 / SI-914-022 current issue;
p – 1x lock washer A6 P/N 945751 is not needed after production-year 2010 on position between the bracket 2 P/N 851267 and the hex nut M6

B – Loctite 243
C – Loctite 648

AR – As required

c – Cooling area 234 cm² / 36.27 sq. in.;
e – UNF connections

a – Marked with S/N

B – Loctite 243
I – Lithium-Base Grease
O – Engine Oil

a – Stator retrofit kits: 912 UL: S/N 3,792.501 up to 3,792.55 Set D P/N 888716, S/N 4,005.300 up to 4,152.111 Set E P/N 888718, S/N 3,792.556 up to 4,005.299, Set C P/N 888714; S/N 4,152.112 up to 4,403.282 Set B P/N 888712; 912 ULS: S/N 4,425.001 up to 4,425.029 Set A P/N 888710; 914 UL: S/N 4,417.503 up to 4,417.783 Set B S/N 888712;
b – With modified trigger, instead of 4° before top dead center --> -3° after top dead center;
c – SI-912-013 / SI-914-016 standardization of the ignition unit;
d – Trigger coil kit with elongated hole for adjustment and 6-pole connector incl. 7 Stk. P/N 827800;
e – 4-pole connector and trigger coils without alignment incl. 7 Stk. P/N 827800. Replaced trigger coil kit P/N 965177;
f – Trigger coils for rev. counter to P/N 965176 and P/N 965179;
g – At all trigger coils with longhole

B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
P – Loctite 5910

a – Only for model 2 and 4;
b – Tolerance group "C" 1.820 - 1.829 mm;
c – Tolerance group "C" 1.830 - 1.839 mm;
d – See Overhaul Manual of the respective engine type, current issue

B – Loctite 243
L – Klueber Isoflex Topas Nb5051AR – As required

a – For cylinder 2 and 4;
b – From engine 912 UL S/N 4,401.595 up to 4,402.978, 914 UL S/N 4,417.708 up to 4,417.727;
c – From engine 912 UL S/N 4,402.979, 914 UL S/N 4,417.728;
d – Up to engine 912 UL S/N (Only if the engine was not refitted with intake manifolds 867683 and 867688) 4,402.978, 914 UL S/N 4,417.727;
e – Only at intake manifold without O-ring;
f – See following Service Bulletin SB-912-030 / current issue SB-914-019;
g – Not suitable for direct installation of the air filter on the carburetor. Forseen for airboxes without drip tray;
h – For rework of exhaust port. See Maintenance Manual Heavy of the respective engine type, current issue;
i – In a roll;
j – See Service Instruction SI-914-020 / current issue SI-914-022;
k – For cylinder 1 and 3;
l – Intake manifold with connection boss for pneumatic carburetor-synchronization. From engine 912 UL S/N 4,404.045, 912 ULS 4,426.475, 914 UL 4,417.956