Genuine ROTAX Parts

B – Loctite 243
I – Lithium-Base Grease

a – In a roll/Sold by the meter (39")

B – Loctite 243
I – Lithium-Base Grease

a – In a roll/Sold by the meter (39")

I – Lithium-Base Grease
X – Adhesive

AR – As required

AR – As required

a – For E-starter position 93 or 183 degrees;
b – Air guide, carburetor side;
c – Air guide, exhaust side

A – Loctite 221
I – Lithium-Base Grease

AR – As required

a – For electric starter, configuration magneto-side or pto side;
b – In a roll/Sold per meter (39");
e – Retrofittable from engine S/N 4,103.549

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
J – Molykote 44 Medium

c – Up to engine S/N 582 UL Mod. 90 4,172.691 (see also SI-08-1994);
d – From engine S/N 582 UL Mod. 90 4,172.692 (see also SI-08-1994)

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
J – Molykote 44 Medium

a – Red 76,00 - 76,01mm, Green 76,01 - 76,02mm;
b – For configuration without 2-piece radiator;
c – For configuration with 2-piece radiator

B – Loctite 243
F – Loctite 480
I – Lithium-Base Grease

AR – As required

a – For ignition circuit 1;
b – For ignition circuit 2;
c – To fix oil tube resp. cable harness;
d – Sold by the meter (39")

B – Loctite 243
E – Anti-Seize
I – Lithium-Base Grease
O – Engine Oil

a – From engine S/N 582 UL Mod. 90 5,236.549 piston for monohook circlip configuration (see also SI-2ST-001);
b – With 2 rings, standard;
c – With 2 rings, 1st oversize;
d – with 2 rings, 2nd oversize;
e – Standard size;
f – 1st oversize;
g – 2nd oversize; 
h – For use with piston Part No. 888 590 (Also see SI-2ST-001);
i – Use only once

A – Loctite 221
C – Loctite 648
I – Lithium-Base Grease

a – From engine S/N 582 UL DCDI mod. 90: 4,015.239, 582 UL DCDI mod. 99: at serial production;
b – For ignition circuit 1;
c – For ignition circuit 2;
d – Up to engine S/N 582 UL DCDI mod. 90: 4,015.238;
e – From engine S/N 582 UL DCDI mod. 90: 4,015.239, 582 UL DCDI mod. 99: at serial production;
f – Sold by the meter (39");
g – Without rewind starter

Q – 732 RTV

AR – As required

a – Use at 582 UL mod. 90;
b – Use at 582 UL mod. 99;
c – Not available as spare part, use 881460

a – For cylinder;
b – For cylinder exhaust flange;
c – For rotary valve shaft;
d – For ball bearing, rotary valve shaft;
e – For oil seal rotary valve shaft (wihout oil pump), intake side;
f – For oil seal rotary valve shaft (with oil pump), intake side;
g – For inner oil seal rotary valve shaft, water pump side;
h – For outer oil seal rotary valve shaft, water pump side;
i – To press in the rotary seal;
j – For rotary valve timing;
k – To pull out the rotary seal - the inner steel bushing of the rotary seal has to be removed before demounting!;
l – For fitting of piston pin circlip;
m – For fitting of piston pin circlip (monohook circlip);
q – To press in the rotary seal 850942 with the insertion jig

A – Loctite 221

a – For configuration without oil pump