Search results for 'Oil'

a – Useable for engine type 447 UL, 503 UL, 582 UL 90/99 and 618 UL;
b – For adjustment and control of the ignition timing;
c - To cover the crankcase;
d – To hold the oil pump gear;
e – To hold the magneto flywheel;
f – For magneto fly wheel;
g – For ball bearing 6206, crankshaft magneto side;
h – For ball bearing 6207, crankshaft;
i – For ring halves;
j – For puller;
k – For crankshaft PTO side;
l – For crankshaft magneto side;
m – For ball bearing

B – Loctite 243
E – Anti-Seize
I – Lithium-Base Grease
O – Engine Oil

a – From engine S/N 582 UL Mod. 90 5,236.549 piston for monohook circlip configuration (see also SI-2ST-001);
b – With 2 rings, standard;
c – With 2 rings, 1st oversize;
d – with 2 rings, 2nd oversize;
e – Standard size;
f – 1st oversize;
g – 2nd oversize; 
h – For use with piston Part No. 888 590 (Also see SI-2ST-001);
i – Use only once

a – For cylinder;
b – For cylinder exhaust flange;
c – For rotary valve shaft;
d – For ball bearing, rotary valve shaft;
e – For oil seal rotary valve shaft (wihout oil pump), intake side;
f – For oil seal rotary valve shaft (with oil pump), intake side;
g – For inner oil seal rotary valve shaft, water pump side;
h – For outer oil seal rotary valve shaft, water pump side;
i – To press in the rotary seal;
j – For rotary valve timing;
k – To pull out the rotary seal - the inner steel bushing of the rotary seal has to be removed before demounting!;
l – For fitting of piston pin circlip;
m – For fitting of piston pin circlip (monohook circlip);
q – To press in the rotary seal 850942 with the insertion jig

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
O – Engine Oil

a – 582 UL DCDI mod. 99 rotary valve for configuration with rotary seal;
b – 582 UL DCDI mod. 99 the circlip must be positioned at the inner groove only;
e – Crankcase including rotary valve drive, configuration with rotary seal model 99

a – For internal hex. screw;
b – To remove the gear cover;
c – To compress the dog gear;
d – For drive gear, I=2,00, I=2,24, I=2,58;
e – For oil seal 850055;
f – For gearbox configuration "B";
g – For oil seal 930715;
h – For oil seal 950085 and 950084;
i – For oil seal 933675;
j – To remove the layshaft gear; 
k – To remove the flywheel; 
l – For mounting the hardy disk;
m – For gearbox configuration "C";
n – For gearbox configuration "E"

A – Loctite 221
E – Anti-Seize
I – Lithium-Base Grease
O – Engine Oil

a – With 2 rings, standard;
b – With 2 rings, 1st oversize;
c – With 2 rings, 2nd oversize;
d – standard size;
e – 1st oversize;
f – 2nd oversize;
g – ATTENTION: Use only once!

A – Loctite 221
E – Anti-Seize
I – Lithium-Base Grease
O – Engine Oil

a – With 2 rings, Standard;
b – With 2 rings, 1st Oversize;
c – With 2 rings, 2nd Oversize;
d – Standard Size;
e - 1st Oversize;
f – 2nd Oversize;
g – ATTENTION: Use only once

L – Klueber Isoflex Topas Nb5051
O – Engine Oil

a – For gear sets P/N 886125, 886517; thin dog gear (22 mm / 0.87 in.)
b – For gear set P/N 886518; wide dog gear (27 mm / 1.06 in.)
c – With additional bores to drain lead
d – Option for 912 UL fitted with 2,43 gear set

A – Loctite 221
C – Loctite 648
E – Loctite Anti-Seize
I – Lithium-Base Grease

AR – As required

a – Replace layshift gear 55 T and pinion shaft 21 T only together;
b – Replace layshift gear 57 T and pinion shaft 19 T only together;
c – Replace layshift gear 59 T and pinion shaft 17 T only together;
d – Replace layshift gear 60 T and pinion shaft 15 T only together;
e – Attention: Left handed thread;
f – Coupling-flange Part No. 958 971 and oil-seal Part No. 950 084 has to be used together;
h – Gear set and splitted cone sleeve 847 757 must be used together. Also see SI-2ST-007

Used with Rotax 12mm Oil Hose and Parker 1/2 ID Oil Hose.

When choosing a clamp, measure the outside diameter of your hose or tube with the fitting installed.

AR – As required

a – For specific use see installation sheet;
b – Use at intake silencer version;
c – For 582 UL mod. 90 without fresh oil injection;
d – With fresh oil injection