Search results for 'Gearbox type c'

C – Loctite 638
L – Klueber Isoflex Topas Nb5051
O – Engine Oil

AR – As required

a – For cylinder 2 and 3;
b – For cylinder 1 and 4;
c – Up to engine S/N 912 UL: 4,401.879, 914 UL: 4,417.597, single valve springs and double valve springs if required are allowed to be mounted in one engine;  
d – From engine S/N 912 UL: 4,401.880, 914 UL: 4,417.598;
e – With sintered bronze bushing;
f – Oversize +0.2 mm (0.008 in.);
g – Rocker arm version with vespel bushing, from engine S/N 912 UL: 4,404.621, 912 ULS: 4,427.487, 914 UL: 4,418.104;
h – For inlet valve, chafe up to new measurement;
i –  For outlet valve, chafe up to new measurement;
j – Use only once!;
k – For rework of exhaust port. See Overhaul Manual of the respective engine type, current issue;
l – Marked with S/N;
m – Without worm gear;
n – Prefilled, 8 parts per set;
o – Cylinder heads where the coolant temperature is measured.
p – see SI-914-30

B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
P – Loctite 5910

a – marked with S/N;
b – Only for model 2 and 4;
c – Tolerance group "C" 1.820 - 1.829 mm;
d – Tolerance group "D" 1.830 - 1.839 mm;
e – Depending on configuration use 14 studs P/N 840752 M8x201 or 8 studs M8x201 and 6 studs P/N 840754 m8x210;
f – See Overhaul Manual of the respective engine type, current issue;
g – Only for use with new cylinders 913221 with countersunk. With the cylinder 913225 the countersunk was already introduced starting from beginnng of the production;
h – See the following Service Instruction current issue SI-914-021;
i – Without O-Ring from S/N 06.0010 to 07.5000, 2x O-Ring starting with S/N 07.5001;
j – 431570 introduced as per engine S/N as follows: 912 UL S/N 06,770.893, 912 ULS S/N 06,781.191, 914 UL S/N 07,682.596;
k – Wrench size A/F 11

B – Loctite 243
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
P – Loctite 5910

a – Stainless;
b – Optional for engine suspension frame;
c – The rotary seal was introduced from following S/N. Up to this S/N the rotary seal has to be exchanged together with P/N 850945, 926273, 922224: 912 UL 4,403.283, 912 ULS starting with serial production, 914 UL 4,417.783;
d – For mech. rev counter drive without centering bore for pick up. For engines without mech. rev. counter drive P/N 230880, 945750, 840511 has to be mounted additional; 
e – See SB-914-023 current issue;
f – See Maintenance Manual Heavy of the respective engine type, current issue;
g - Without processing for mech. rev counter drive;
h – Will be delivered in circle shape.

B – Loctite 243
L – Klueber Isoflex Topas Nb5051AR – As required

a – For cylinder 2 and 4;
b – From engine 912 UL S/N 4,401.595 up to 4,402.978, 914 UL S/N 4,417.708 up to 4,417.727;
c – From engine 912 UL S/N 4,402.979, 914 UL S/N 4,417.728;
d – Up to engine 912 UL S/N (Only if the engine was not refitted with intake manifolds 867683 and 867688) 4,402.978, 914 UL S/N 4,417.727;
e – Only at intake manifold without O-ring;
f – See following Service Bulletin SB-912-030 / current issue SB-914-019;
g – Not suitable for direct installation of the air filter on the carburetor. Forseen for airboxes without drip tray;
h – For rework of exhaust port. See Maintenance Manual Heavy of the respective engine type, current issue;
i – In a roll;
j – See Service Instruction SI-914-020 / current issue SI-914-022;
k – For cylinder 1 and 3;
l – Intake manifold with connection boss for pneumatic carburetor-synchronization. From engine 912 UL S/N 4,404.045, 912 ULS 4,426.475, 914 UL 4,417.956

a – Measure group "c" 1.830 - 1.839 mm, b – Measure group "C" 1.830 - 1.839 mm, c - Until crankcase SN 12.0122

b – For mixture lubrication;
c – For oil pump version

b – For mixture lubrication;
c – For oil pump version

a – RED 67.50 MM - 67.51 MM, GREEN 67.51 - 67.52 MM;
b – Cylinder PTO side;
c – Cylinder MAG side