Search results for 'SPARK PLUGS AND ACCESSORIES'

b - Double ignition coil with high tension threaded connection, c - Double ignition coil and ignition cable with plug connection

B – Loctite 243

a – Note Service Instruction SI-912-005 current issue

A – Loctite 221
B – Loctite 243
C - Loctite 648

c – Tighten to leave 1mm distance between starter cover and electric starter

B – Loctite 243
I - Lithium-Base Grease
AG – Silicon Heat Compound

a – Sold by the meter (39");
e – Not necessary at intake manifold P/N 867688;
f – Introduced as S/N 04.0388 with altered insulation only for spare parts;
g – Not suitable for crankcase P/N 886354, P/N 886358 and older;
h – At crankcase P/N 888364 or newer crankcase;
i – Not suitable for intake manifold P/N 867688;
j – Necessary at version with ring mount;
k – Sold by the meter (39");
l – Use P/N 842742 and 953390 only together;
m – SI-912-013 / SI-914-016 current issue. See Maintenance Manual Heavy of the respective engine type, current issue. From engine 912 UL S/N 4,406.291, 912 ULS S/N 5,643.680, 914 UL 4,418.712;
n - In a roll, silicone hose 120 mm;
o – SI-912-020 / SI-914-022 current issue;
p – 1x lock washer A6 P/N 945751 is not needed after production-year 2010 on position between the bracket 2 P/N 851267 and the hex nut M6

a – For installation of cylinder on the piston 67.5 mm;
b – For installation of cylinder on the piston 72 mm;
c – To hold the fan;
d – For aligning of cylinders at the intake flange;
e – For crankshaft bearing PTO side;
f – For positioning of crankshaft bearing PTO side;
g – For centering of the stator plate;
h – For piston pin 18 mm;
i – For installation of piston pin circlip 18 mm;
j – For the engine;
k – Without ignition and externals

F – Loctite 7063
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
Z – Loctite 603

e – At 912 ULS the complete  piston with rings has to be exchanged up to S/N 4,425.123;
f – With countersunk for O-ring 830415. 912 UL: 4,403.679, 912 ULS: Starting with serial production, 914 UL: 4,417.868;
g – Note following Service Letter: SL-912-002 current issue, SL-914-002 current issue,
h – With expanded space of sprag clutch. Introduced as per following engine S/N 912 UL: 4,409.089, 912 ULS: 5,650.835, 914 UL: 6,772.727;
i - Balanced pistons set: max. difference 3 g

B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
P – Loctite 5910

a – Only for model 2 and 4;
b – Tolerance group "C" 1.820 - 1.829 mm;
c – Tolerance group "C" 1.830 - 1.839 mm;
d – See Overhaul Manual of the respective engine type, current issue

L – Klueber Isoflex Topas Nb5051

a - See SB-914-023 current issue;
b – Wil be delivered in circle shape;
c – Standard starter 0.7 kW;
d – Washer, lock washer and hex. nut replaced by hex. collar nut

a – For internal hex. screw;
b – To remove the gear cover;
c – To compress the dog gear;
d – For drive gear, I=2,00, I=2,24, I=2,58;
e – For oil seal 850055;
f – For gearbox configuration "B";
g – For oil seal 930715;
h – For oil seal 950085 and 950084;
i – For oil seal 933675;
j – To remove the layshaft gear; 
k – To remove the flywheel; 
l – For mounting the hardy disk;
m – For gearbox configuration "C";
n – For gearbox configuration "E"

B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
P – Loctite 5910

a – marked with S/N; 
b – Only for model 2 and 4; 
c – Tolerance group "C" 1.820 - 1.829 mm;
d – Tolerance group "D" 1.830 - 1.839 mm; 
e – Depending on configuration use 14 studs P/N 840752 M8x201 or 8 studs M8x201 and 6 studs P/N 840754 m8x210;
f – See Overhaul Manual of the respective engine type, current issue;
g – Only for use with new cylinders 913221 with countersunk. With the cylinder 913225 the countersunk was already introduced starting from beginning of the production;
h – See the following Service Instruction current issue SI-914-021.

B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
P – Loctite 5910

a – marked with S/N;
b – Only for model 2 and 4;
c – Tolerance group "C" 1.820 - 1.829 mm;
d – Tolerance group "D" 1.830 - 1.839 mm;
e – Depending on configuration use 14 studs P/N 840752 M8x201 or 8 studs M8x201 and 6 studs P/N 840754 m8x210;
f – See Overhaul Manual of the respective engine type, current issue;
g – Only for use with new cylinders 913221 with countersunk. With the cylinder 913225 the countersunk was already introduced starting from beginnng of the production;
h – See the following Service Instruction current issue SI-914-021;
i – Without O-Ring from S/N 06.0010 to 07.5000, 2x O-Ring starting with S/N 07.5001;
j – 431570 introduced as per engine S/N as follows: 912 UL S/N 06,770.893, 912 ULS S/N 06,781.191, 914 UL S/N 07,682.596;
k – Wrench size A/F 11

C – Loctite 638
L – Klueber Isoflex Topas Nb5051
O – Engine Oil

AR – As required

a – For cylinder 2 and 3;
b – For cylinder 1 and 4;
c – Up to engine S/N 912 UL: 4,401.879, 914 UL: 4,417.597, single valve springs and double valve springs if required are allowed to be mounted in one engine;  
d – From engine S/N 912 UL: 4,401.880, 914 UL: 4,417.598;
e – With sintered bronze bushing;
f – Oversize +0.2 mm (0.008 in.);
g – Rocker arm version with vespel bushing, from engine S/N 912 UL: 4,404.621, 912 ULS: 4,427.487, 914 UL: 4,418.104;
h – For inlet valve, chafe up to new measurement;
i –  For outlet valve, chafe up to new measurement;
j – Use only once!;
k – For rework of exhaust port. See Overhaul Manual of the respective engine type, current issue;
l – Marked with S/N;
m – Without worm gear;
n – Prefilled, 8 parts per set;
o – Cylinder heads where the coolant temperature is measured.
p – see SI-914-30

AR – As required

a – If installed with filter on top;
b – If installed with filter on bottom;
c – not available as a spare part

B – Loctite 243

AR – As required

B – Loctite 243
E – Loctite Anti-Seize 15378

AR – As required

e – For cylinder head;
f – For EGT sensor;
g – For exhaust gas temperature (EGT);
h – For thermo couple NiCr-Ni K;
i – Stainless, for EGT sensor;
j – With service reset button and USB-connector;
k – See Service Instruction SI-912-020 / SI-914-022 current issue

B – Loctite 243

AR – As required

a – Supply to cylinder 1 and 2; b – Supply to cylinder 3 and 4; c – Discharge cylinder 1; d – As scrab-protector for version 3; e – Discharge cylinder 3; f – Discharge cylinder 2; g – Discharge cylinder 4; h – Sold by the meter (39"); i – Expansion tank for radiator installation above engine; j – See SI-912-020 + SI-914-022 current issue; k – See SB-914-043 current issue

B – Loctite 243
L – Klueber Isoflex Topas Nb5051AR – As required

a – For cylinder 2 and 4;
b – From engine 912 UL S/N 4,401.595 up to 4,402.978, 914 UL S/N 4,417.708 up to 4,417.727;
c – From engine 912 UL S/N 4,402.979, 914 UL S/N 4,417.728;
d – Up to engine 912 UL S/N (Only if the engine was not refitted with intake manifolds 867683 and 867688) 4,402.978, 914 UL S/N 4,417.727;
e – Only at intake manifold without O-ring;
f – See following Service Bulletin SB-912-030 / current issue SB-914-019;
g – Not suitable for direct installation of the air filter on the carburetor. Forseen for airboxes without drip tray;
h – For rework of exhaust port. See Maintenance Manual Heavy of the respective engine type, current issue;
i – In a roll;
j – See Service Instruction SI-914-020 / current issue SI-914-022;
k – For cylinder 1 and 3;
l – Intake manifold with connection boss for pneumatic carburetor-synchronization. From engine 912 UL S/N 4,404.045, 912 ULS 4,426.475, 914 UL 4,417.956

B – Loctite 243
I – Lithium-Base Grease
O – Engine Oil

a – Stator retrofit kits: 912 UL: S/N 3,792.501 up to 3,792.55 Set D P/N 888716, S/N 4,005.300 up to 4,152.111 Set E P/N 888718, S/N 3,792.556 up to 4,005.299, Set C P/N 888714; S/N 4,152.112 up to 4,403.282 Set B P/N 888712; 912 ULS: S/N 4,425.001 up to 4,425.029 Set A P/N 888710; 914 UL: S/N 4,417.503 up to 4,417.783 Set B S/N 888712;
b – With modified trigger, instead of 4° before top dead center --> -3° after top dead center;
c – SI-912-013 / SI-914-016 standardization of the ignition unit;
d – Trigger coil kit with elongated hole for adjustment and 6-pole connector incl. 7 Stk. P/N 827800;
e – 4-pole connector and trigger coils without alignment incl. 7 Stk. P/N 827800. Replaced trigger coil kit P/N 965177;
f – Trigger coils for rev. counter to P/N 965176 and P/N 965179;
g – At all trigger coils with longhole

A – Loctite 221
Q – Silastic 732 RTV

AR – As required

a – Cooling surface 3,2 dm² (49,6 in²);
b – From engine S/N: 3,916.823;
c – Up to engine S/N: 4,916.822;
d – For evacuation of air, at installation of engine with spark plugs down;
e – Longer studs for 582 UL Mod. 90. Not used on 582-99;
f – Sold by the meter (39”)

A – Loctite 221
B – Loctite 243
Q – Silastic 732 RTV

AR – As required

a – Cooling surface 3,2 dm² (49,6 in²);
b – From engine S/N: 3,916.823;
c – Up to engine S/N: 4,916.822;
d – For evacuation of air, at installation of engine with spark plugs down;
e – Longer studs for 582 UL Mod. 90. Not used on 582-99;
f – Sold by the meter (39”)