Search results for 'Ignition Parts'

a - Air filter incl. hose clamp, b - Double flange, c - Ambient pressure and temperature

a – Marked with S/N

B – Loctite 603

a – Version 4.6, used from following engine S/N 914 UL from 4,417.849. Retrofit at older engines possible according SB/SI, Marked with S/N;
b – Marked with S/N;
c – Airbox pressure sensor;
d – See Service Instruction SI-914-022 current issue;
e – Only for P/N 966741 (version 4.6);
f – For authorized distributors only;
g – Connector cable, wiring harness P/N 966492 with sensor P/N 274051. See Service Instruction SI-914-022;
h – Non-certified part

A – Loctite 221
D – Loctite 574

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
O – Engine Oil

a – 582 UL DCDI mod. 99 rotary valve for configuration with rotary seal;
b – 582 UL DCDI mod. 99 the circlip must be positioned at the inner groove only;
e – Crankcase including rotary valve drive, configuration with rotary seal model 99

F – Loctite 7063
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
Z – Loctite 603

e – At 912 ULS the complete  piston with rings has to be exchanged up to S/N 4,425.123;
f – With countersunk for O-ring 830415. 912 UL: 4,403.679, 912 ULS: Starting with serial production, 914 UL: 4,417.868;
g – Note following Service Letter: SL-912-002 current issue, SL-914-002 current issue,
h – With expanded space of sprag clutch. Introduced as per following engine S/N 912 UL: 4,409.089, 912 ULS: 5,650.835, 914 UL: 6,772.727;
i - Balanced pistons set: max. difference 3 g

H – Oil filter

d – See Service Instruction SI-912-017 current issue

AR – As required

B – Loctite 243
I – Lithium-Base Grease
O – Engine Oil

a – Stator retrofit kits: 912 UL: S/N 3,792.501 up to 3,792.55 Set D P/N 888716, S/N 4,005.300 up to 4,152.111 Set E P/N 888718, S/N 3,792.556 up to 4,005.299, Set C P/N 888714; S/N 4,152.112 up to 4,403.282 Set B P/N 888712; 912 ULS: S/N 4,425.001 up to 4,425.029 Set A P/N 888710; 914 UL: S/N 4,417.503 up to 4,417.783 Set B S/N 888712;
b – With modified trigger, instead of 4° before top dead center --> -3° after top dead center;
c – SI-912-013 / SI-914-016 standardization of the ignition unit;
d – Trigger coil kit with elongated hole for adjustment and 6-pole connector incl. 7 Stk. P/N 827800;
e – 4-pole connector and trigger coils without alignment incl. 7 Stk. P/N 827800. Replaced trigger coil kit P/N 965177;
f – Trigger coils for rev. counter to P/N 965176 and P/N 965179;
g – At all trigger coils with longhole

a – Measure group "c" 1.830 - 1.839 mm, b – Measure group "C" 1.830 - 1.839 mm, c - Until crankcase SN 12.0122

A – Loctite 221
C – Loctite 648
I – Lithium-Base Grease

a – From engine S/N 582 UL DCDI mod. 90: 4,015.239, 582 UL DCDI mod. 99: at serial production;
b – For ignition circuit 1;
c – For ignition circuit 2;
d – Up to engine S/N 582 UL DCDI mod. 90: 4,015.238;
e – From engine S/N 582 UL DCDI mod. 90: 4,015.239, 582 UL DCDI mod. 99: at serial production;
f – Sold by the meter (39");
g – Without rewind starter

B – Loctite 243

a – Marked with S/N. Inclusive suction and pressure line;
b – Marked with S/N;
c – With fuel pressure gauge connection, At conversion from 956312 to 956602 remove jet 963820 from banjo bolt;
d – Marked with yellow dot;
e – Drip tray for airbox P/N 867758, 667162 and 667167,
f – Drip tray for airbox P/N 867758,
g – For retrofitting see Service Bulletin SB-912-044 current issue;
h – Optional with connection flexible fuel lines;
i – See SI 912-020 current issue;
j – For steel pipe

447 UL – 29.5 kW
503 UL – 34 kW
582 UL

a – Base carburetor for air-cooled engines with bowden cable choke. NOTICE carburetor without calibration. From engine S/N 447 UL: 3,940.675, 503 UL: 4,795.201;
b – Base carburetor for liquid cooled engines with bowden cable choke. NOTICE carburetor without calibration; From engine S/N 582 UL Mod. 90: 4,656.088, 582 UL mod. 99: starting with serial production;
c – Carburetor housing, not available as spare part, use carburetor assy.;
d – Jet-needle, see carburetor calibration sheet;
e – Idle-jet, see carburetor calibration sheet;
f – Needle-jet, see carburetor calibration sheet;
g – Main-jet, see carburetor calibration sheet;
h – Only necessary on high altitude compensation kit (not available anymore)

O – Engine Oil

a – See SB-912-040, SB-914-026 current issue;
b – In a roll;
c – With metric connection thread M18x1.5

AR – As Required 

a – break away torque 700-900 Nm/516.2 ft.lb - 663.8 ft.lb., b – break away torque 600-800 Nm/442.5 ft.lb - 590 ft.lb.