Search results for 'Ignition Coils'

B – Loctite 243
I - Lithium-Base Grease
AG – Silicon Heat Compound

a – Sold by the meter (39");
e – Not necessary at intake manifold P/N 867688;
f – Introduced as S/N 04.0388 with altered insulation only for spare parts;
g – Not suitable for crankcase P/N 886354, P/N 886358 and older;
h – At crankcase P/N 888364 or newer crankcase;
i – Not suitable for intake manifold P/N 867688;
j – Necessary at version with ring mount;
k – Sold by the meter (39");
l – Use P/N 842742 and 953390 only together;
m – SI-912-013 / SI-914-016 current issue. See Maintenance Manual Heavy of the respective engine type, current issue. From engine 912 UL S/N 4,406.291, 912 ULS S/N 5,643.680, 914 UL 4,418.712;
n - In a roll, silicone hose 120 mm;
o – SI-912-020 / SI-914-022 current issue;
p – 1x lock washer A6 P/N 945751 is not needed after production-year 2010 on position between the bracket 2 P/N 851267 and the hex nut M6

B – Loctite 243
I – Lithium-Base Grease
O – Engine Oil

a – Stator retrofit kits: 912 UL: S/N 3,792.501 up to 3,792.55 Set D P/N 888716, S/N 4,005.300 up to 4,152.111 Set E P/N 888718, S/N 3,792.556 up to 4,005.299, Set C P/N 888714; S/N 4,152.112 up to 4,403.282 Set B P/N 888712; 912 ULS: S/N 4,425.001 up to 4,425.029 Set A P/N 888710; 914 UL: S/N 4,417.503 up to 4,417.783 Set B S/N 888712;
b – With modified trigger, instead of 4° before top dead center --> -3° after top dead center;
c – SI-912-013 / SI-914-016 standardization of the ignition unit;
d – Trigger coil kit with elongated hole for adjustment and 6-pole connector incl. 7 Stk. P/N 827800;
e – 4-pole connector and trigger coils without alignment incl. 7 Stk. P/N 827800. Replaced trigger coil kit P/N 965177;
f – Trigger coils for rev. counter to P/N 965176 and P/N 965179;
g – At all trigger coils with longhole

A – Loctite 221
C – Loctite 648
I – Lithium-Base Grease

a – From engine S/N 582 UL DCDI mod. 90: 4,015.239, 582 UL DCDI mod. 99: at serial production;
b – For ignition circuit 1;
c – For ignition circuit 2;
d – Up to engine S/N 582 UL DCDI mod. 90: 4,015.238;
e – From engine S/N 582 UL DCDI mod. 90: 4,015.239, 582 UL DCDI mod. 99: at serial production;
f – Sold by the meter (39");
g – Without rewind starter

A – Loctite 221
I – Lithium-Base Grease

a – For ignition circuit 1;
b – For ignition circuit 2;
c – From engine S/N 4,795.397;
d – Sold by the meter (39");
e – Magneto flywheel new version (with closed cage), torx screw also valid for old version. At disassembly and reassembly of the screw, the thread has to be cleaned of the remaining coating and secured with Loctite 221. As an alternative a new screw can be used.

AR – As required

a – For E-starter position 93 or 183 degrees;
b – Air guide, carburetor side;
c – Air guide, exhaust side

AR – As required

a – Air guide, carburetor side;
b – Air guide, exhaust side

B – Loctite 242
F – Loctite 380
I – Lithium-Base Grease

AR – As required

a – For ignition circuit 1, b – For ignition circuit 2, c – To fix oil tube resp. cable harness, d – In a roll/sold per meter (39")

B – Loctite 243
F – Loctite 480
I – Lithium-Base Grease

AR – As required

a – For ignition circuit 1;
b – For ignition circuit 2;
c – To fix oil tube resp. cable harness;
d – Sold by the meter (39")

Ignition Cable Set 665668 replaces individual cable assemblies 665550, 665551, 665552, 665553, 665554, 665555, 665556, 665557

b - Double ignition coil with high tension threaded connection, c - Double ignition coil and ignition cable with plug connection

a – Useable for engine type 447 UL, 503 UL, 582 UL 90/99 and 618 UL;
b – For adjustment and control of the ignition timing;
c - To cover the crankcase;
d – To hold the oil pump gear;
e – To hold the magneto flywheel;
f – For magneto fly wheel;
g – For ball bearing 6206, crankshaft magneto side;
h – For ball bearing 6207, crankshaft;
i – For ring halves;
j – For puller;
k – For crankshaft PTO side;
l – For crankshaft magneto side;
m – For ball bearing

a – For installation of cylinder on the piston 67.5 mm;
b – For installation of cylinder on the piston 72 mm;
c – To hold the fan;
d – For aligning of cylinders at the intake flange;
e – For crankshaft bearing PTO side;
f – For positioning of crankshaft bearing PTO side;
g – For centering of the stator plate;
h – For piston pin 18 mm;
i – For installation of piston pin circlip 18 mm;
j – For the engine;
k – Without ignition and externals